The comparison selection method of hard foam silicone oil

Rigid foam leveling agent (hereinafter referred to as “silicone oil”) model selection and dosage definition is of great importance, it is directly related to the final product of the foam pore structure, shrinkage resistance, insulation and other actual performance advantages and disadvantages.

Experimental object

Conventional in the use of rigid foam silicone oil as a reference A, compared to the unknown performance of rigid foam silicone oil B, C, D, E, etc.

Test apparatus

(Here only highlight the part that is different from the conventional test)

1, variable speed hand drill: 300w or so, the speed can be adjusted by knob gear.

2, about 100ml size of disposable transparent plastic drinking cup: to be slightly harder, so as not to stir when holding deformation difficult to pinch.

Blank master batch preparation example

A, high moisture, low density type manual slow material

Polyether 4110: 100

Water: 1.8

Cyclohexylamine: 1.0~2.0 (depending on the ambient temperature and material temperature control)

141B:25

Second, low moisture, high density type manual slow material

Polyether 4110:100

Water: 0.5

Cyclohexylamine: 1.0~2.0 (depending on the ambient temperature and material temperature control)

141B: 7

The total amount of the above blank material preparation depends on the number of silicone oil types to be compared to the whole n times enlarged. Overall fully shaken and divided into n equal parts.

Foam]

A. High moisture, low silicone oil, low density type manual slow material

Add 0.5 parts of A, B, C and D silicone oil to n equal parts of blank material, shake well and let it stand to see its compatibility and transparency.

Adjust the speed of variable speed hand drill to the right gear: make sure the mixing speed is “medium slow”, never allow high shear fast gear mixing.

Within 20 minutes, each component with 0.5 parts of silicone oil will be foamed at the same speed, the same ratio (about 12g white material + 12g black material) and the same mixing time.

Reminder: Don’t break the mushroom head. After foaming and shaping, we can only make marks at the bottom of the cup separately in order to be objective and fair when comparing.

Second, low moisture, low silicone oil, high-density manual slow material

Operation with (i), about 20 grams of white material + 20 grams of black material

C. High moisture, high silicone oil, low density hand-made slow material

The test (i) in each section of the remaining white material proportional to the amount of their respective silicone oil to 1.0 parts, and then the same conditions foaming

Fourth, low moisture, high silicone oil, high density type manual slow material

The remaining white materials in test (ii) will be proportionally increased to 1.0 parts of their respective silicone oil, and then the same conditions foaming

Comparison, analysis]

Test one of the foam mixed together with the naked eye to distinguish the apparent bubble hole advantages and disadvantages (bubble hole fine density, uniformity), and then look at the bottom to determine the ranking of these silicone oil.

Mixing the foams in test three together with the naked eye to distinguish the apparent pore strengths and weaknesses (pore density, uniformity), and then looking at the bottom to determine the ranking of these silicone oils.

And then one, three experiments in the same silicone oil type of different amounts of foam body put together to compare, to see the amount of silicone oil to increase the fine density of pores, uniformity has improved significantly

Second, four between the same

If necessary, a sharp cutting edge can be used to compare the internal pores

Special note]

Usually, the silicone oil with good bubble pore under slow stirring has better performance under high shear stirring, especially the combination of materials to resist “abnormal fluctuation of process parameters during injection molding” (such as: power supply voltage fluctuations, power frequency abnormalities, minor blockage, material viscosity abnormalities) ability is better.

Call Us

+971 55 906 6368

Email: jarveyni@zafchemllc.com

Working hours: Monday to Friday, 9:00-17:30 (GMT+8), closed on holidays
Scan to open our site

Scan to open our site

Home
whatsapp
Product
Contact